LED - Light Emitting Diode is a semiconductor device which converts electricity into light. LED lighting has been around since the 1960s, but is just now beginning to appear in the residential market for space lighting. At first white LEDs were only possible by "rainbow" groups of three LEDs -- red, green, and blue -- by controlling the current to each to yield an overall white light. Standard array 18 LED lighting diodesThis changed in 1993 when Nichia created a blue indium gallium chip with a phosphor coating that is used to create the wave shift necessary to emit white light from a single diode. This process is much less expensive for the amount of light generated.

Each diode is about 1/4 inch in diameter and uses about ten milliamps to operate at about a tenth of a watt. LEDs are small in size, but can be grouped together for higher intensity applications. LED fixtures require a driver which is analogous to the ballast in fluorescent fixtures. The drivers are typically built into the fixture (like fluorescent ballasts) or they are a plug transformer for portable (plug-in) fixtures. The plug-in transformers allow the fixture to run on standard 120 volt alternating current (AC), with a modest (about 15 to 20 percent) power loss.

The efficacy of a typical residential application LED is approximately 20 lumens per watt (LPW), though efficacies of up to 100 LPW have been created in laboratory settings. Incandescent bulbs have an efficacy of about 15 LPW and ENERGY STAR® qualified compact fluorescents are about 60 LPW, depending on the wattage and lamp type. Some manufacturers claim efficacies much higher than 20 LPW; make sure to examine system efficacy, which accounts for the power use of all components. In December 2006, the U.S. Department of Energy studied the efficacy of four luminaries. All four fell short of the manufacturers’ claims; the study implies that manufacturers are relying on measurements of how much light an isolated LED produces, rather than how much light an LED luminaire actually delivers.

LEDs are better at placing light in a single direction than incandescent or fluorescent bulbs. Because of their directional output, they have unique design features that can be exploited by clever designs. LED strip lights can be installed under counters, in hallways, and in staircases; concentrated arrays can be used for room lighting. Waterproof, outdoor fixtures are also available. Some manufacturers consider applications such as gardens, walkways, and decorative fixtures outside garage doors to be the most cost-efficient.

LEDs are available in red, orange, amber, yellow, green, blue and white. Blue and white LEDs are much more expensive than the other colours. The colour of an LED is determined by the semiconductor material, not by the colouring of the 'package' (the plastic body). LEDs of all colours are available in uncoloured packages which may be diffused (milky) or clear (often described as 'water clear'). The coloured packages are also available as diffused (the standard type) or transparent.

Three-Color LEDs :

The most popular type of tri-colour LED has a red and a green LED combined in one package with three leads. They are called tri-colour because mixed red and green light appears to be yellow and this is produced when both the red and green LEDs are on. The diagram shows the construction of a tri-colour LED. Note the different lengths of the three leads. The centre lead (k) is the common cathode for both LEDs, the outer leads (a1 and a2) are the anodes to the LEDs allowing each one to be lit separately, or both together to give the third colour.

Two-Color LEDs :

A bi-colour LED has two LEDs wired in 'inverse parallel' (one forwards, one backwards) combined in one package with two leads. Only one of the LEDs can be lit at one time and they are less useful than the tri-colour LEDs described above.

Caution :

Connecting several LEDs in parallel with just one resistor shared between them is generally not a good idea. If the LEDs require slightly different voltages only the lowest voltage LED will light and it may be destroyed by the larger current flowing through it. Although identical LEDs can be successfully connected in parallel with one resistor this rarely offers any useful benefit because resistors are very cheap and the current used is the same as connecting the LEDs individually. If LEDs are in parallel each one should have its own resistor.